Author |
Message |
fwd_3kgt
|
Posted: Thu Feb 12, 2009 9:24 am |
|
Joined: Tue Feb 19, 2008 12:17 am Posts: 295 Location: Sheboygan, Waukesha
|
A923KGT wrote: is your car a 2nd gen? I might have an axle for you. It's from an auto tranny car, but I think one axle is the same as the manual and one is different. so if you want to research and find out, you can have the axle IF you come take it off the car. I'll go check at auto zone if it makes any difference. But the 2.5 hour drive is a bit far. But I'll consider it.
|
|
Top |
|
|
fwd_3kgt
|
Posted: Thu Feb 12, 2009 9:27 am |
|
Joined: Tue Feb 19, 2008 12:17 am Posts: 295 Location: Sheboygan, Waukesha
|
jeettao wrote: Dude that is utter crap. Gotta get that fixed before any major meets. You should be able to pick up a used axle for less than 125. Doing my best at the moment. I can get a "reman" axle for 74.95 and bring my broken one in, or try to pick one up for less if possible. And hope that it's in good condition.
|
|
Top |
|
|
jeettao
|
Posted: Thu Feb 12, 2009 2:35 pm |
|
Joined: Tue May 25, 2004 8:37 pm Posts: 236
|
fwd_3kgt wrote: jeettao wrote: Dude that is utter crap. Gotta get that fixed before any major meets. You should be able to pick up a used axle for less than 125. Doing my best at the moment. I can get a "reman" axle for 74.95 and bring my broken one in, or try to pick one up for less if possible. And hope that it's in good condition. Are there any decent part-out threads on 3si?
|
|
Top |
|
|
fwd_3kgt
|
Posted: Thu Feb 12, 2009 3:25 pm |
|
Joined: Tue Feb 19, 2008 12:17 am Posts: 295 Location: Sheboygan, Waukesha
|
at the moment, there is nothing. I found a few though. But shipping for the axle alone is $30+ and everyone I asked won't go lower then 50 for it. LoL. So I rather just get a reman axle if it's going to cost that much. Otherwise, my best chance is to find one on here. I think I have already, not 100% sure yet. Just have to confirm it.
|
|
Top |
|
|
jeettao
|
Posted: Fri Feb 13, 2009 4:36 pm |
|
Joined: Tue May 25, 2004 8:37 pm Posts: 236
|
fwd_3kgt wrote: at the moment, there is nothing. I found a few though. But shipping for the axle alone is $30+ and everyone I asked won't go lower then 50 for it. LoL. So I rather just get a reman axle if it's going to cost that much. Otherwise, my best chance is to find one on here. I think I have already, not 100% sure yet. Just have to confirm it. Yeah I hear ya.
|
|
Top |
|
|
fwd_3kgt
|
Posted: Fri Feb 13, 2009 8:40 pm |
|
Joined: Tue Feb 19, 2008 12:17 am Posts: 295 Location: Sheboygan, Waukesha
|
Does anyone have any plans this spring? Doing anything to their 3s? Share what you are going to be doing! lol. I'm bored and we need to be a bit more active, even though there is only a few of us.
|
|
Top |
|
|
Jhammer
|
Posted: Fri Feb 13, 2009 11:19 pm |
|
Joined: Mon May 23, 2005 11:25 am Posts: 605 Location: Waukesha. WI
|
Quote: Does anyone have any plans this spring? Doing anything to their 3s? <--- fixing a spun bearing. Maybe I will have a car again this spring.
_________________ 1993 3000GT VR-4 (build in progress)
1994 3000GT SL
Lead, Follow, or get out of my way!
Also know as:
"dead weight", "wrong wheel drive noob"
|
|
Top |
|
|
fwd_3kgt
|
Posted: Fri Feb 13, 2009 11:40 pm |
|
Joined: Tue Feb 19, 2008 12:17 am Posts: 295 Location: Sheboygan, Waukesha
|
how far are you on this? Have you even started? lol. Hope to see you around this summer then! I'll be down there in waukesha a few time summer.
|
|
Top |
|
|
jeettao
|
Posted: Sat Feb 14, 2009 2:00 am |
|
Joined: Tue May 25, 2004 8:37 pm Posts: 236
|
Well, I've got a 16G setup with supporting mods and an AEM EMS. But I'm running a tune that's only set for 1 bar right now, so, I'm thinking I'm going to toss on a meth injection kit and then tuning it to run about 22-23 psi (whatever she can handle).
|
|
Top |
|
|
jeettao
|
Posted: Sat Feb 14, 2009 2:01 am |
|
Joined: Tue May 25, 2004 8:37 pm Posts: 236
|
Jhammer wrote: Quote: Does anyone have any plans this spring? Doing anything to their 3s? <--- fixing a spun bearing. Maybe I will have a car again this spring. I hope this goes well, good luck to you, Jham.
|
|
Top |
|
|
Jhammer
|
Posted: Sat Feb 14, 2009 10:44 am |
|
Joined: Mon May 23, 2005 11:25 am Posts: 605 Location: Waukesha. WI
|
Quote: how far are you on this? Have you even started? the tear down of the engine is going on as we speak. I just need to get over this flu bug I am fighting so I can get back out to my shop again. grrrrr
_________________ 1993 3000GT VR-4 (build in progress)
1994 3000GT SL
Lead, Follow, or get out of my way!
Also know as:
"dead weight", "wrong wheel drive noob"
|
|
Top |
|
|
fwd_3kgt
|
Posted: Sat Feb 14, 2009 10:49 pm |
|
Joined: Tue Feb 19, 2008 12:17 am Posts: 295 Location: Sheboygan, Waukesha
|
sounds great then. Hopefully you get it done before the end of spring.
|
|
Top |
|
|