| Author |
Message |
|
rjnelson4
|
 Posted: Thu Dec 22, 2005 3:58 pm |
|
Joined: Mon Sep 12, 2005 10:47 pm
Posts: 22
Location: Stoughton
|
|
I thought the seal on my transfercase from the transmission was leaking. It is acctually the seal on the transmission between the transfercase and trany. Can I replace this seal with the tranny in the car?
_________________
1991 Mitsubishi 3kgt VR4
6spd manual transmission conversion
130,000 milles
Black/tan
|
|
| Top |
|
 |
|
G-ELL
|
Posted: Fri Dec 23, 2005 3:36 pm |
|
Joined: Wed Aug 13, 2003 1:18 am
Posts: 3153
Location: Lehigh Valley, PA
|
|
My mind is drawing a blank.
Isn't there only a seal for the input sleeve for the t-case. Not for the output shaft on the tranny?
|
|
| Top |
|
|
|
rjnelson4
|
Posted: Fri Dec 23, 2005 4:53 pm |
|
Joined: Mon Sep 12, 2005 10:47 pm
Posts: 22
Location: Stoughton
|
|
there is one on the output shaft to the transfercase. Its between the tranny and transfercase kind of deep in the tranny. Im trying to pull the side cover in order to pull out the shaft, so I can remove the seal. Any other ideas?
_________________
1991 Mitsubishi 3kgt VR4
6spd manual transmission conversion
130,000 milles
Black/tan
|
|
| Top |
|
|
|
G-ELL
|
Posted: Fri Dec 23, 2005 5:27 pm |
|
Joined: Wed Aug 13, 2003 1:18 am
Posts: 3153
Location: Lehigh Valley, PA
|
|
Can't pull the output shaft/vcu out in a 6-speed with the tranny still in the car. It's been tried/failed before.
Where did you get your 6-speed from?
_________________ 06 Blue EVO 9
|
|
| Top |
|
|
|
rjnelson4
|
Posted: Fri Dec 23, 2005 6:46 pm |
|
Joined: Mon Sep 12, 2005 10:47 pm
Posts: 22
Location: Stoughton
|
|
I did it!!!!!!!!!!!!! I cant pull the VCU but I did pull the out put shaft. Now all I have to do is order the seal. Just wanted to let everyone know that it is possible. Maybee I can do it because its in a 91.
_________________
1991 Mitsubishi 3kgt VR4
6spd manual transmission conversion
130,000 milles
Black/tan
|
|
| Top |
|
|
|
G-ELL
|
Posted: Sun Dec 25, 2005 12:04 am |
|
Joined: Wed Aug 13, 2003 1:18 am
Posts: 3153
Location: Lehigh Valley, PA
|
rjnelson4 wrote: I did it!!!!!!!!!!!!! I cant pull the VCU but I did pull the out put shaft. Now all I have to do is order the seal. Just wanted to let everyone know that it is possible. Maybee I can do it because its in a 91. Curious. Did you use a bearing puller to grab onto the end load bearing and pull it out thru the passenger side of the case?
|
|
| Top |
|
|
|
rjnelson4
|
Posted: Sun Dec 25, 2005 9:18 pm |
|
Joined: Mon Sep 12, 2005 10:47 pm
Posts: 22
Location: Stoughton
|
|
I tapped the pins out in the casing around the shaft. The shaft slide right out with no problems. I cant remove the casing because of gears that get in the way.
_________________
1991 Mitsubishi 3kgt VR4
6spd manual transmission conversion
130,000 milles
Black/tan
|
|
| Top |
|
|
